[Koha] Indexing Not Updating

[Katrin Fischer]

Hi,

I think the problem might not be the indexing itself, but that your
Zebra server is not running.

This might help:
sudo service restart koha-common

Then you can do:
ps axf | grep "zebrasrv"

To see if it's running.

Hope this helps,

Katrin

Am 28.12.2015 um 21:19 schrieb Bruce A. Metcalf:
> On 12/27/2015 12:25 PM, Bruce A. Metcalf wrote:
> 
>>>>> I wonder if you still have other path issues, or it might be the
>>>>> switch
>>>>> from grs1 to dom. What version did you upgrade from ?
>>>> I think it was Version 3.12 that you helped me install at KohaCon13
>>>> (thanks
>>>> again). I've since been upgrading each release as it comes out using
>>>> packages.
>>> Ahh that may be it, take a look at
>>> http://wiki.koha-community.org/wiki/Switching_to_dom_indexing
>>>
>>> We tend to not try to update the config file automatically as we might
>>> accidentally clobber some of your intentional changes, so it might be
>>> that it hasn't switched to DOM
>>>
>>> I'd back up the file, make the changes, restart the zebraserver
>>> (service koha-common restart) run a full reindex (koha-rebuild-zebra
>>> -f) and see if that fixes it, you can always roll back if it doesn't
>> It doesn't.
>>
>> The instructions say to check "/About Koha/ > /System information"/
>> for GRS1/DOM-related warnings. I see two warnings:
>>
>> > Warning    You are missing the <log4perl_conf> entry in your
>> koha-conf.xml file.
>> > Warning    You are missing the <upload_path> entry in your
>> koha-conf.xml file.
>>
>> I can't say if these were there previously, and neither appears to be
>> related.
>>
>> I also notice that in "/About Koha/ > /Server information"/ there's an
>> error that does seem related:
>>
>> *> Error *Zebra server seems not to be available. Is it started?
>>
>> Perhaps this is a clue?
> 
> In the absence of new ideas, I have tried switching to the indexing
> daemon using by:
> 
> - Comment the rebuild_zebra.pl line in /etc/cron.d/koha-common
> - Enable the indexer daemon in /etc/default/koha-common
> - Restart Koha's daemons:
>   $ sudo service koha-common stop ; sudo service koha-common start
> 
> I also looked at my zebra-error.log, which turns out to be filled with
> this sequence, repeating every 30 seconds:
> 
> 20151228 15:16:48 library-koha-zebra: client (pid 20683) exited with 1
> status
> 
> 20151228 15:16:48 library-koha-zebra: client (pid 20684) exited with 1
> status
> 
> 20151228 15:16:48 library-koha-zebra: client (pid 20685) exited with 1
> status
> 
> 20151228 15:16:48 library-koha-zebra: client (pid 20686) exited with 1
> status
> 
> 20151228 15:16:48 library-koha-zebra: client (pid 20687) exited with 1
> status
> 
> 20151228 15:16:48 library-koha-zebra: terminating too quickly, waiting
> 30 seconds
> 
> 
> Note that this log tail was observed after switching to the indexing
> daemon.
> 
> Lots of data, very little understanding here!
> 
> Thanks in advance,
> Bruce A. Metcalf
> Augustan Society Library
> 
> _______________________________________________
> Koha mailing list  http://koha-community.org
> Koha at lists.katipo.co.nz
> https://lists.katipo.co.nz/mailman/listinfo/koha